Big Order? No Problem! Financing available through QUADPAY or PAYPAL 0% 6 Months Approval is Quick & Easy.
Don't see what you need? Call 740-939-0073 or LIVE CHAT. 10am-6pm Eastern
¡Todos los kits de barras de tracción tienen precios mejorados, distintivos FFS y hardware incluidos! ¡Más completo y asequible que nunca! Estas pi...
View full details
Bolts, FFS Badges and Caster Eliminator Plates Sold Separately. Add from menu on right. This is for a pair of Radius Long Arm links to replace your...
View full details
Dana 60 kingpin crossover steering kit utilizing hd tie rod ends. This is a DIY kit to switch from the short rearward facing drag link on your Chev...
View full details
Ring and the Cover are 3/8" thick Plate steel cover bent 8 ways Machined absolutely flat for a perfect fit All seams fully welded inside and out...
View full details
Front Adjustable Radius Arm, Ford Super Duty Dana 60 05-22 Want a better radius arm? Want any adjustability at all? Want to add a little posi...
View full details
Take a Dana 60 front axle from an 05 and up Ford Super Duty donor truck, and this Radius Arm Kit, and put it under about any frame you want. Or bui...
View full details
This is your not so basic steering setup that uses 7/8" Heims with easier adjustment & much stronger tubing. The kit can be used over or under ...
View full details
When adding a High Angle end in your Drag Link (on our Y-Link kit or crossover kit) you need to increase the diameter of the taper in your pitman ...
View full details
These U-bolt plates are for the Dodge Dana 60 King Pin front axle. The Unique Plate for the passenger side is 1/2" thick without bends to deal w...
View full details
These are the ideal way to set up the bottom link of any 3 or 4 link suspension and these are almost 3 pounds each! We make them .25 thick with a g...
View full details
2 Laser cut 3/16 traction bar or link arm FarFromStock Badges. Can be welded on through the eyelets but also can be secured with #10 hardware. We a...
View full details
1.5 inch o.d. DOM Tubing, .250 (1/4”) wall material thickness. Sold by the foot, from 2-6’.
1-2"x1/4" wall DOM 1-Sleeves for a 9/16" 2-High quality bushings Sold individually 2-5/8 mounting width
These are a new take on an old idea. Radius arms have been around a long time, I don't think Ford was the first. The old part is simply the modific...
View full details
1g Long Travel Air Suspension Kit This is the real deal in suspension modification for your 72** through 93 Dodge single wheel truck. 13+ inches of...
View full details
Here is something a lot of you guys using a 2005 and newer Ford F250/F350 Superduty Axle will appreciate. This bracket will mount to the factory ra...
View full details
Qty(2) 1.25" Rod End Set 12(TPI) Rod ends without misalignments and tube adapters Unloaded rod ends
This is a HEX Head Weld in Threaded Bung for your link suspension, this one is the big guy made for the bottom of the truck. The side that's ...
View full details
THIS KIT IS DESIGNED FOR PEOPLE THAT HAVE SWAPPED A DUALLY REAR AXLE INTO SOMETHING ELSE UTILIZING SINGLE REAR WHEELS. MAY WORK ON A DUAL REAR W...
View full details
NOTE: THE CUSTOM WIDTH MINIMUM DISTANCE CAN NOT BE LESS THAN 2 1/4 OD OR MORE THAN 4" These are designed with an offset so you can pull them way b...
View full details
This bracket is for those of you running wider than stock width axles. Made out of 1/4" plate, it has an ID of 2" and mounts on the outside of the ...
View full details
This weld-on bracket is part of our TJ Axle Swap Kit that adapts the popular Ford 8.8" rear end to the stock suspension mounts in your Jeep Wrangle...
View full details
NOTE: Product sold unwelded This is a simple idea that we should have come up with a long time ago. There are several situations where the lower li...
View full details
Offset Panhard / Trackbar bracket. It has 3 mounting position options, 4", 5", & 6" from axle center. They are cut for a 3" axle tube diameter ...
View full details
This link Tab is made for truss and frame use, anything with a flat surface. It, and all of our Link Single Tabs are a seriously strong .375" (3/8)...
View full details
These are the bolts you need for the Pumkin side of a D44 and are pretty much standard, The exception being that they are .625" (5/8) rolled thread...
View full details
.25" plate it is lighter and smaller to fit into tighter spaces. These have a 2 5/8" inside mounting width They are sold individually and come unwe...
View full details
It is made for the cruiser weight axles out there like D44, D60, Ford 9", Ford 8.8's, Toyota Mini's, Toyota Land Cruisers, Chrysler 8.25's and a wh...
View full details
Sale
This is your not so basic steering setup that mocks the factory setup with easier adjustment & much stronger tubing. The kit can be used with s...
View full details
Track bar kit for your custom suspension. Front or rear, but if you do rear and want the frame end on the driver side you will need to modify the o...
View full details
Sale
Optima 34/78 battery (W: 6.94" L: 10.06" H: 6.62") Battery box dimensions are L: 10.125" W: 15" We are very particular about how these go togethe...
View full details
Sale
Fits Optima 34/78 battery Battery dimensions W:6.94" L:10.06" H:6.62" We made these with the Fabricator in mind. These are made of 1 piece of ste...
View full details
Rear 4 Link Builder Kit for full size trucks. This kit is especially good for trucks that have a fuel tank in front of the axle and inside the fr...
View full details
This is it, a pair of FFS 1.25” Heat Treated Chromoly Rod Ends with all the trimmings! You get two 1.25" Heims with a 1" through bore, 4 zinc plate...
View full details
6 bolt tube clamp for 1.5" outside diameter tube. Made from 1/2" wall chromoly tube and uses 1/4" allen head bolts. Great for mounting ram assist o...
View full details
6 bolt tube clamp for 1.25" outside diameter tube. Made from 1/2" wall chromoly tube and uses 1/4" allen head bolts. Great for adding a stabilizer ...
View full details